德国Evoqua
Evoqua W3T441749
型号: W3T441749
ULTRA CLEAR RO EDI 20
Pure water production from softened
potable tap water. The system combines
the technology of the reverse osmosis
with the final deionization of the
permeate by single bed electro-deionization. The system is placed in a welldesigned plastic housing.
The reverse osmosis component mainly
consists of:
1 Solenoid valve for raw water
1 Pre-treatment module AMD, fine filter
made of plastic, inclusive active
carbon/fine filter cartridge 5 µm,
front-side operated
1 Pressure switch as pump protection
1 High pressure pump made of brass with
magnetic-coupled E-motor
1 Pressure gauge to indicate operating
pressure
1 Module set with spiral-wound
membranes, made of polyamide on a
polysulphone basis, incl. pressure
vessel with end caps
1 Solenoid valve for permeate reject
when conductivity is exceeded
1 Conductivity meter for permeate
1 Restrictor for limiting the concentrate quantity
The Ionpure component mainly
consists of:
1 Ionpure cell, two-pass, with chambers
for anion and cation exchange resin
and brine chambers, anodes, cathodes,
ion-selective membranes and end plates
1 Conductivity meter for pure water
1 Restrictor for limiting the brine
1 Conditioning cartridge
Control:
Display with membrane keyboard with
monitor for:
- Conductivity permeate and pure water
- Level indication storage tank
in Percent for level sensors or
fixed value for float switches
- 3 free selectable switching activating points ON/OFF and running dry
protection for booster pump
- Status indication via symbols
- Indications for maintenance intervals and replacement of cartridge
- Fault indication (insufficient raw
water, insufficient permeate, conductance LF1 / LF 2)
- Timer program for displacement of
concentrate and module flushing
- RS 232 interface
(processing software optional)
- Multilingualism
1 set connecting hoses
1 filter cup wrench
1 operator's manual
Performance specifications:
- Production rate at 15°C: 20 l/h
- Conductivity: < 0.2 µS/cm
- typical conductivity: 0.07 µS/cm
- Silicate content: < 10 ppb
- TOC value: < 30 ppb
- particle rejection: > 99 %
Feed water specifications:
- Flow rate: 30 - 44 l/h
- Pressure: 0.1 - 5 bar
- Maximum conductivity: < 1400 µS/cm
- SDI: < 3
- FE and free chlorine: < 0,1 mg/l
- CO2 value in the feed: < 10 mg/l
- max. SiO2 value in the feed: < 10 mg/l
- Permissible water temp.: 5 - 30°C
Technical data:
- Operating pressure: max. 6 bar
- Electrical power: 100-240V, 50-60 Hz
- Current consumption: 0.2 kW
- Fuse: 16 A
- Permissible ambient temp.: 5 - 35°C
Connections:
Raw water: 3/4"
Pure water: d= 8 mm
Drain concentrate: d= 8 mm
Drain brine: d= 6 mm
Dimensions and Weight:
Height: 530 mm
Width: 340 mm
Depth: 420 mm
Weight: 32 kg
Please note:
The performance is based on a raw water
salt content of max. 750 mg/l (TDS)
equivalent to a conductivity of 1400 µS/cm
at 15°C. From 10°dH or higher, a softener is
recommended. All a. m. components are
assembled into a complete system.
The Ultra Clear RO EDI can be put
into operation without the help of a
factory service engineer.
The feed water specifications are guidelines. The pure water specifications can
only be guaranteed, if a drinking water
analysis is available for the plant
location and all other relevant
parameters have been evaluated by Evoqua.
推荐产品 更多产品...
Evoqua W3T441749 基本属性
净重:32.000 KG
毛重:38.400 KG
长度:530 mm
宽度:340 mm
高度:420 mm